ISSN   1004-0595

CN  62-1095/O4

高级检索
徐翔, 张祖悦, 王兴华, 黄柏军, 秦红玲, 赵新泽. 不同固体润滑下人字闸门底枢摩擦特性的销盘试验研究[J]. 摩擦学学报, 2022, 42(5): 1044-1052. DOI: 10.16078/j.tribology.2021202
引用本文: 徐翔, 张祖悦, 王兴华, 黄柏军, 秦红玲, 赵新泽. 不同固体润滑下人字闸门底枢摩擦特性的销盘试验研究[J]. 摩擦学学报, 2022, 42(5): 1044-1052. DOI: 10.16078/j.tribology.2021202
XU Xiang, ZHANG Zuyue, WANG Xinghua, HUANG Baijun, QIN Hongling, ZHAO Xinze. Experimental Study on Friction Characteristics of Miter Gate Bottom Pivot with Different Solid Lubrication[J]. TRIBOLOGY, 2022, 42(5): 1044-1052. DOI: 10.16078/j.tribology.2021202
Citation: XU Xiang, ZHANG Zuyue, WANG Xinghua, HUANG Baijun, QIN Hongling, ZHAO Xinze. Experimental Study on Friction Characteristics of Miter Gate Bottom Pivot with Different Solid Lubrication[J]. TRIBOLOGY, 2022, 42(5): 1044-1052. DOI: 10.16078/j.tribology.2021202

不同固体润滑下人字闸门底枢摩擦特性的销盘试验研究

Experimental Study on Friction Characteristics of Miter Gate Bottom Pivot with Different Solid Lubrication

  • 摘要: 人字闸门底枢长期在水下的低速重载下运行,易出现由磨损导致的故障,为此,三峡五级船闸的闸门已采用油脂和固体润滑剂混合润滑方式以减少摩擦磨损. 为了研究石墨、二硫化钼和聚四氟乙烯固体粉末对底枢摩擦副材料(45钢和锡青铜)摩擦学性能的影响,以三峡人字闸门底枢为研究对象,依据计算结果设计销/盘配对副面结构,在MMW-1A立式万能摩擦磨损试验机上开展磨损试验研究,并结合表面三维形貌测试和铁谱测试对摩擦磨损结果进行分析,结果表明:在试验条件下,聚四氟乙烯的摩擦系数最小,石墨次之,二硫化钼的摩擦系数最大;磨损量从小到大依次为石墨、聚四氟乙烯和二硫化钼;石墨润滑条件下磨损形式仅为单一的黏着磨损,二硫化钼和聚四氟乙烯润滑条件下磨损形式为黏着磨损和疲劳磨损,且石墨润滑产生的磨粒粒径要小于二硫化钼和聚四氟乙烯润滑产生的磨粒粒径,综上认为石墨是三者中性质较优的固体润滑剂. 在此基础上开展了石墨润滑下的13 h连续磨损试验,得到其摩擦系数和磨损量的变化规律,为人字闸门底枢摩擦副的固体润滑设计提供理论依据.

     

    Abstract: The miter gates act as an important part of the hydro-junction, and they take into account two functions: shipping and power generation. Their bottom pivots work under low speed and heavy load underwater for a long time, and applying grease as a single lubricant is easy to cause poor lubrication. Practice has proved that friction and wear were important reasons for the failure of the bottom pivot of the miter gate. In order to further extend the maintenance cycle and improve the service life, the gate of the five-level ship lock in the Three Gorges had been lubricated with grease and solid lubricant to reduce friction and wear. Graphite, MoS2 and PTFE are the three most commonly used solid lubricants in industry. In order to study the effect of these three kinds solid lubricant powder and grease on the tribological performance of the bottom pivot matching pair materials (45 steel and tin bronze), the bottom pivot of the Three Gorges miter gate was taken as the research object, the pin-disk matching pair surface structure was designed according to calculated the maximum contact stress and maximum operating speed, and the filling hole’s size was obtained according to the similarity theory. The three kinds of solid lubricant powder and binder were mixed in a certain proportion to form mixed fillers and fill in the filling holes, and the filler was solidified at 80℃ for 12 hours, and ensured the filler was flush with the disk’s surface. Then the wear test was carried out on the MMW-1A tester after the disk’s surface was coated with grease, and the friction and wear results were analyzed in combination with three-dimensional surface morphology test and ferrography test. The results showed that under the experimental conditions, the friction coefficient of PTFE was the minimum, followed by graphite, and the friction coefficient of MoS2 was the maximum, and the average friction coefficients were 0.25, 0.18 and 0.09 in one hour, respectively; the wear amount of the disk specimen, average wear depth and wear weight from small to large were graphite, PTFE and MoS2. Compared with the surface parameters before wear, in addition to the graphite lubrication condition, the surface root mean square value (Sq) and the surface arithmetic average value (Sa) decreased, the other values showed an upward trend. Meantime, under the graphite lubrication condition, the wear form was only single adhesive wear, and under the MoS2 or PTFE lubrication condition, the wear form were mixed wear formed by adhesive wear and fatigue wear, and the particle sizes of particles produced by graphite lubrication were smaller than that produced by MoS2 and PTFE lubrication. Therefore, it was considered that graphite was the better solid lubricant among these. On this basis, the continuous wear test for 13 h under graphite lubrication was carried out, the experiment results showed the average friction coefficient and wear mass indicated an overall trend of first decreasing and then increasing with time, which provided a theoretical basis for the solid lubrication design of the bottom pivot friction pair of miter gate.

     

/

返回文章
返回